List Index out of bounds

This Forum is for Support questions only for Ideal Flight. Please post other questions and suggestions in the General Use & Ideas Forum

Moderators: Steve Waite, SysAdmin

Re: List Index out of bounds

Postby Brent » Thu May 17, 2018 4:30 pm

Steve, I started a flight, pushed back and then ended the flight with out saving the new location. The 'browse airport' page worked fine.

Brent
Brent
 
Posts: 200
Joined: Thu Aug 02, 2012 5:38 pm

Re: List Index out of bounds

Postby Steve Waite » Thu May 17, 2018 4:38 pm

That means it must have to add your score. Forgot about the move to new location. Can you move a few yards and exit the flight and save the new location?

I just landed and parked up. Accepted the tick and before doing anything else, with code in place to capture the error I went to the browse map page and...no error so far.
software architect at codelegend.com
equipment: i9-9980Xe 64GB 2xRTX2080ti NVLink 2TB M.2 NVMe,
i9-9900X 64GB RTX2080ti 2TB M.2 NVMe, i7-3960X 32GB GTX680 4TB RAID10,
NAS @7TB RAID10 (16TB)
Steve Waite
 
Posts: 5055
Joined: Wed Jun 29, 2011 12:02 am

Re: List Index out of bounds

Postby Steve Waite » Thu May 17, 2018 4:40 pm

Brent, by the way I presume you are using IF10 original? [sm]
software architect at codelegend.com
equipment: i9-9980Xe 64GB 2xRTX2080ti NVLink 2TB M.2 NVMe,
i9-9900X 64GB RTX2080ti 2TB M.2 NVMe, i7-3960X 32GB GTX680 4TB RAID10,
NAS @7TB RAID10 (16TB)
Steve Waite
 
Posts: 5055
Joined: Wed Jun 29, 2011 12:02 am

Re: List Index out of bounds

Postby Brent » Thu May 17, 2018 5:05 pm

Hi Steve - I started a flight, moved a bit and then ended the flight. IF reminded me I was in a flight, accepted and saved new location (check mark). IF gave me this 'Flight Prep' page: I can't remember if there's something amiss there (no flight plan details!)

Image

This time I received the out of bounds error message when I went to the browse airport page.

I am using IF10 original [sm].

Thanks
Brent
i7-7700k, ASUS Z170 Pro Gaming, Asus GeForce GTX 970, 32Gb, TM Warthog HOTAS, W10 64bit, DX10 FSX with Accel
Brent
 
Posts: 200
Joined: Thu Aug 02, 2012 5:38 pm

Re: List Index out of bounds

Postby Steve Waite » Thu May 17, 2018 5:24 pm

When we accept a new parking location we have to build a new flight after that so the old flight is gone, that's fine.

But we are getting warmer perhaps? You only need to accept a new location, and before doing anything else go to the map page, the map page does not appear as it stays on the main page but the controls go blank?
software architect at codelegend.com
equipment: i9-9980Xe 64GB 2xRTX2080ti NVLink 2TB M.2 NVMe,
i9-9900X 64GB RTX2080ti 2TB M.2 NVMe, i7-3960X 32GB GTX680 4TB RAID10,
NAS @7TB RAID10 (16TB)
Steve Waite
 
Posts: 5055
Joined: Wed Jun 29, 2011 12:02 am

Re: List Index out of bounds

Postby Brent » Thu May 17, 2018 5:41 pm

When I accept the new location, IF takes me to the main page as shown above. When I select the browse airport page, IF blanks out on me and gives me the error message.
Brent
 
Posts: 200
Joined: Thu Aug 02, 2012 5:38 pm

Re: List Index out of bounds

Postby Steve Waite » Thu May 17, 2018 5:42 pm

That narrows it down a lot since it doesn't involve updating the score.

So long as you have been to the Flight Gen page first the map page will go in?
software architect at codelegend.com
equipment: i9-9980Xe 64GB 2xRTX2080ti NVLink 2TB M.2 NVMe,
i9-9900X 64GB RTX2080ti 2TB M.2 NVMe, i7-3960X 32GB GTX680 4TB RAID10,
NAS @7TB RAID10 (16TB)
Steve Waite
 
Posts: 5055
Joined: Wed Jun 29, 2011 12:02 am

Re: List Index out of bounds

Postby Brent » Thu May 17, 2018 5:52 pm

That's correct....but only if I generate a new flight or perform a search of possible destinations.
Brent
 
Posts: 200
Joined: Thu Aug 02, 2012 5:38 pm

Re: List Index out of bounds

Postby Steve Waite » Thu May 17, 2018 6:07 pm

Thanks Brent, that should be enough to go on...
software architect at codelegend.com
equipment: i9-9980Xe 64GB 2xRTX2080ti NVLink 2TB M.2 NVMe,
i9-9900X 64GB RTX2080ti 2TB M.2 NVMe, i7-3960X 32GB GTX680 4TB RAID10,
NAS @7TB RAID10 (16TB)
Steve Waite
 
Posts: 5055
Joined: Wed Jun 29, 2011 12:02 am

Re: List Index out of bounds

Postby Steve Waite » Fri May 18, 2018 3:37 pm

Brent,

This should be a simple bug to find but it's turned out hard to replicate and I've not found the cause of the problem.

Wondering what we can try to see if it changes the outcome - can you try a new profile to see if that has the same issue?
Steve
software architect at codelegend.com
equipment: i9-9980Xe 64GB 2xRTX2080ti NVLink 2TB M.2 NVMe,
i9-9900X 64GB RTX2080ti 2TB M.2 NVMe, i7-3960X 32GB GTX680 4TB RAID10,
NAS @7TB RAID10 (16TB)
Steve Waite
 
Posts: 5055
Joined: Wed Jun 29, 2011 12:02 am

PreviousNext

Return to Support

Who is online

Users browsing this forum: No registered users and 5 guests